$20 off any repair · Same-day service · Diagnostic from $80, credited toward your repair · 60-day warrantyBook online 24/7 →
Home › Repair Guides › Guide

Samsung Washer Problems: Common Issues and Fixes

Quick answer: The most common Samsung washer problems are unbalanced loads that stop the spin, drain blockages in the pump filter, water supply issues, door lock faults and odor in front-load models. Many of these show a code on the display and can be fixed with simple checks. Motor, control board and suspension failures need a technician.
Mr. Fixer technician: washer repair

Washer stops mid-cycle or will not spin

Samsung washers check the balance of the drum before they spin fast. If the load is lopsided, the washer will try to redistribute it, and if it cannot, it may stop the spin or end the cycle with clothes still wet. On many models this shows as a dC, dE or Ub style code, depending on the generation.

  • Open the door and spread the load evenly around the drum.
  • Wash bulky items like comforters, rugs and pet beds on their own, or with a couple of towels to balance them.
  • Avoid washing a single heavy item, such as one pair of jeans or one bath mat.
  • Check that the washer sits level and does not rock when you push on the corners.

If it will not spin even with a small, balanced load, the cause may be a drain issue, worn suspension, a motor problem or a sensor. Our guide to a washing machine not draining or spinning covers the general causes.

Water will not drain

Drain errors are among the most frequent Samsung washer complaints. On many models the code reads 5C, 5E or nd. The most common cause is a clogged pump filter.

On many Samsung front-loaders, the filter sits behind a small cover at the lower front corner. Unplug the washer, put down towels and a shallow pan, and release the water first through the small emergency drain tube if your model has one. Then slowly unscrew the filter, which may let out more water than you expect. Remove coins, hair ties, lint and small socks, rinse it and screw it back firmly.

Also check the drain hose behind the washer for kinks, and make sure it is not pushed too far down into the standpipe. If the filter is clean and the washer still will not drain, the drain pump may have failed.

Washer will not fill or fills slowly

When a Samsung washer cannot get enough water, it commonly shows a 4C or 4E code on many models.

  • Make sure both hot and cold supply valves behind the washer are fully open.
  • Check the fill hoses for kinks, especially after the washer was moved.
  • With the water off and the washer unplugged, unscrew the hoses at the washer and look at the small screens inside the inlets. Sediment can clog them over time. Rinse them gently and reconnect.
  • Confirm other faucets in the home have normal pressure.

If water pressure and hoses are fine but the washer still will not fill, the water inlet valve or the water level sensor is a likely cause, and both are routine technician repairs.

Door lock and start problems

Front-load Samsung washers lock the door before every cycle. If the lock cannot engage, the washer will not start and may show a door code, commonly dC or dE on many models, or a door icon that blinks.

  • Close the door firmly and make sure no clothing is caught in the seal.
  • Check that Child Lock is not turned on. On many models you hold two marked buttons for a few seconds to switch it off.
  • Unplug the washer for a minute to reset the control, then try again.
  • If the door handle or latch is cracked, the lock cannot engage.

A washer that shows no display at all, beeps but will not start, or locks the door and then does nothing usually needs a closer look at the door lock assembly or control. Our general guide on a washer that won't start lists more possibilities.

Too many suds, leaks and odors

High-efficiency Samsung washers use much less water than older machines, so they need HE detergent in small amounts. Too much soap produces excess suds, and on many models the washer pauses and shows Sud or SUD while it tries to break them down. Use the recommended amount, and less if you have soft water.

Extra suds and residue also feed odor. On front-loaders, the rubber door boot traps water and lint in its folds. Wipe the seal dry after the last load of the day, leave the door and detergent drawer open to air out, and run the Self Clean or Pure Cycle feature regularly if your model has one. Our guide to a washer that smells bad goes deeper.

Water on the floor can come from a torn door boot, a loose hose or an overflowing detergent drawer. See our page on a washer leaking water for how to trace it.

Loud spinning, shaking and banging

Some movement during a fast spin is normal. Violent shaking, walking across the floor, or loud banging is not.

  • Shipping bolts. On a newly installed front-loader, make sure the transit bolts on the back were removed. Running the washer with them in place causes severe shaking and can damage it.
  • Leveling. Adjust the feet so all four corners sit firmly on the floor, then tighten the lock nuts.
  • Worn suspension. Shock absorbers on front-loaders and suspension rods on top-loaders wear out, letting the tub knock against the cabinet.
  • Bearing noise. A loud roar or grinding that rises with spin speed often points to worn drum bearings.

For a full walk-through, see our guide to a washer shaking or walking.

When to call for Samsung washer repair

Call a technician if a code keeps returning after the basic checks, if the drum will not turn, if you hear grinding or banging that gets worse, or if the washer will not power on. Motor and inverter faults, control board issues, bearings and suspension parts all need proper diagnosis.

Mr. Fixer is a full washing machine repair service across Metro Atlanta and works on Samsung front-load and top-load models every week. Learn more on our Samsung appliance repair page, or look up a specific code in our Samsung washer error code guide. The $80 diagnostic is credited toward the repair, and you get a written estimate before work starts. Call (678) 866-3669 or book online.

Need it fixed?

Our technicians handle washer repair across Metro Atlanta, usually the same day. Diagnostic from $80, credited toward your repair.

Call (678) 866-3669

FAQs

How do I reset my Samsung washer?

On many models, unplugging the washer or switching off its breaker for about a minute resets the control. Some models also have a button combination for a reset; check the owner's manual. A reset clears a stored code but will not fix the underlying cause.

Why does my Samsung washer say dC or Ub?

On many Samsung washers these codes point to an unbalanced load. Redistribute the clothes, avoid washing one heavy item alone and check that the washer is level. If it happens with small, even loads, have the suspension checked.

Where is the drain filter on a Samsung washer?

On many Samsung front-load washers, the filter is behind a small cover at the lower front of the cabinet. Many top-load models do not have a user-accessible pump filter, so check your manual.

Is my Samsung washer worth repairing?

Often yes. Drain pumps, inlet valves, door locks and suspension parts are routine repairs. Our guide on repair versus replacement and our washer repair cost guide can help you weigh the decision.

Call nowBook online