Frigidaire Dishwasher Error Codes: i10–i60

Quick answer: Frigidaire dishwasher codes usually start with an i: i10 is low water, i20 is a drain problem, i30 is a leak into the base, i40 is a clogged filter, i50 is a motor fault and i60 is a heating fault. Drain and filter codes can often be cleared at home; the rest need a technician.

On Frigidaire models with a display, codes show in the control panel on the top edge or front of the door. Some codes look alarming but are normal messages, such as a countdown number for the delay start or HO while the water is heating. Codes vary by model and series, so use these as a guide alongside your owner's manual. Frigidaire's reset for a drain code is to press Cancel, then turn off the breaker or unplug the dishwasher for 3 minutes.

Frigidaire Dishwasher Error Codes list

i10

Water level too low.

Common causes: Kinked or blocked water line, shutoff valve not fully open.

What you can try: Open the supply valve under the sink fully and check the line for kinks.

Call a technician if: The supply is fine and the tub still fills poorly.

i20

The dishwasher did not drain completely.

Common causes: Disposer knockout plug left in, blocked or pinched drain hose, hose too low, clogged filter.

What you can try: Confirm the disposer knockout plug was removed, check the drain hose, and clean the filter and sump. Then press Cancel and cut power for 3 minutes.

Call a technician if: Water stays in the tub after those steps.

i30

Water is leaking into the base.

Common causes: Loose connection, worn seal, oversudsing, unlevel unit.

What you can try: Turn off the water and power. Use only dishwasher detergent.

Call a technician if: Any time you see water under the unit or the code returns.

i40

Clogged filter or sump from food build-up.

Common causes: Food soil in the glass trap and filter.

What you can try: Clean the glass trap and filter, then run the dishwasher again.

Call a technician if: The code persists.

i50

Possible fault with the wash or drain motor.

Common causes: Motor or control fault.

What you can try: A reset may clear it.

Call a technician if: It returns after a reset.

i60

Water heating system error.

Common causes: Heater, thermistor or wiring fault.

What you can try: Nothing beyond a power reset.

Call a technician if: The code returns.

Loss of power.

Common causes: Outage or tripped breaker.

What you can try: Press Start/Cancel to clear it and start a new cycle.

Call a technician if: It happens without an outage.

CL / Cd

The door is open or not fully latched.

Common causes: Rack, dish or utensil stopping the door.

What you can try: Close and latch the door firmly.

Call a technician if: The door will not close properly.

HO / Hd

Not a fault: the dishwasher is heating water to temperature.

Common causes: Cool incoming water.

What you can try: Wait. Running the kitchen tap until hot before starting shortens the wait.

Call a technician if: It stays on for a very long time on every cycle.

How to clear the code

Press Cancel to stop the cycle.
Turn off the dishwasher's breaker or unplug it for 3 minutes.
Restore power and run a short cycle. If the same i-code returns, the cause is still there.

Codes Frigidaire shows that are not faults

A number from 01 to 24 means Delay Start is set; press Cancel once to start the cycle now. A number from 1 to 199 is just the minutes left. LOC means the door is locked during the cycle, and PRESS START means you need to close the door within a few seconds of pressing Start.

Frigidaire dishwasher repair in Atlanta

If your dishwasher shows i30, i50 or i60, or a drain code keeps coming back, Mr. Fixer can test the parts and give you a written estimate before any work. Call (678) 866-3669 or book online. For typical costs, see what dishwasher repair costs in Atlanta, or visit our Frigidaire page.

Code still showing?

Our technicians repair Frigidaire dishwashers across Metro Atlanta, usually the same day. Diagnostic from $80, credited toward your repair.

Call (678) 866-3669

FAQs

What does i20 mean on a Frigidaire dishwasher?

i20 means the unit did not drain completely. Check the disposer knockout plug, the drain hose and the filter, then press Cancel and cut power for 3 minutes to reset.

Is the i30 code serious?

It means water is getting into the base. Stop using the dishwasher, shut off the water and look for a leak. Oversudsing from the wrong soap is a common cause.

Why does my Frigidaire dishwasher show HO?

HO is not an error. The dishwasher is heating the water before continuing. Colder incoming water makes this take longer.

Codes and meanings vary by model and model year. Check your owner's manual for your exact model.

Frigidaire Dishwasher Error Codes: What They Mean and How to Fix Them